Add command `SetOption94 0/1`

Add command ``SetOption94 0/1`` to select MAX31855 or MAX6675 thermocouple support (#8616)

RELEASENOTES.md

@@ -61,6 +61,7 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
 - Fix escape of non-JSON received serial data (#8329)
 - Add command ``Rule0`` to change global rule parameters
 - Add command ``Time 4`` to display timestamp using milliseconds (#8537)
+- Add command ``SetOption94 0/1`` to select MAX31855 or MAX6675 thermocouple support (#8616)
 - Add commands ``LedPwmOn 0..255``, ``LedPwmOff 0..255`` and ``LedPwmMode1 0/1`` to control led brightness by George (#8491)
 - Add support for unique MQTTClient (and inherited fallback topic) by full Mac address using ``mqttclient DVES_%12X`` (#8300)
 - Add more functionality to ``Switchmode`` 11 and 12 (#8450)
@@ -69,6 +70,7 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
 - Add support for VEML7700 Ambient light intensity Sensor by device111 (#8432)
 - Add Three Phase Export Active Energy to SDM630 driver
 - Add Zigbee options to ``ZbSend`` to write and report attributes
+- Add Zigbee auto-responder for common attributes
 - Add ``CpuFrequency`` to ``status 2``
 - Add ``FlashFrequency`` to ``status 4``
 - Add support for up to two BH1750 sensors controlled by commands ``BH1750Resolution`` and ``BH1750MTime`` (#8139)

tasmota/CHANGELOG.md

@@ -7,6 +7,7 @@
 - Change Adafruit_SGP30 library from v1.0.3 to v1.2.0 (#8519)
 - Fix escape of non-JSON received serial data (#8329)
 - Add command ``Time 4`` to display timestamp using milliseconds (#8537)
+- Add command ``SetOption94 0/1`` to select MAX31855 or MAX6675 thermocouple support (#8616)
 - Add commands ``LedPwmOn 0..255``, ``LedPwmOff 0..255`` and ``LedPwmMode1 0/1`` to control led brightness by George (#8491)
 - Add Three Phase Export Active Energy to SDM630 driver
 - Add wildcard pattern ``?`` for JSON matching in rules

tasmota/my_user_config.h

@@ -612,12 +612,12 @@
 // -- Low level interface devices -----------------
 #define USE_DHT                                  // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor (1k6 code)
 
-//#define USE_MAX31855                             // Add support for MAX31855 K-Type thermocouple sensor using softSPI
+//#define USE_MAX31855                             // Add support for MAX31855/MAX6675 K-Type thermocouple sensor using softSPI
 //#define USE_MAX31865                             // Add support for MAX31865 RTD sensors using softSPI
-  #define MAX31865_PTD_WIRES  2                 // PTDs come in several flavors. Pick yours
+  #define MAX31865_PTD_WIRES  2                  // PTDs come in several flavors. Pick yours
-  #define MAX31865_PTD_RES    100               // Nominal PTD resistance at 0°C (100Ω for a PT100, 1000Ω for a PT1000, YMMV!)
+  #define MAX31865_PTD_RES    100                // Nominal PTD resistance at 0°C (100Ω for a PT100, 1000Ω for a PT1000, YMMV!)
-  #define MAX31865_REF_RES    430               // Reference resistor (Usually 430Ω for a PT100, 4300Ω for a PT1000)
+  #define MAX31865_REF_RES    430                // Reference resistor (Usually 430Ω for a PT100, 4300Ω for a PT1000)
-  #define MAX31865_PTD_BIAS   0                 // To calibrate your not-so-good PTD
+  #define MAX31865_PTD_BIAS   0                  // To calibrate your not-so-good PTD
 
 // -- IR Remote features - all protocols from IRremoteESP8266 --------------------------
 // IR Full Protocols mode is activated through platform.io only.

tasmota/xsns_39_max31855.ino

@@ -18,20 +18,27 @@
 */
 
 #ifdef USE_MAX31855
+/*********************************************************************************************\
+ * MAX31855 and MAX6675 - Thermocouple
+ *
+ * SetOption94 0 - MAX31855
+ * SetOption94 1 - MAX6675
+\*********************************************************************************************/
 
 #define XSNS_39              39
 
-bool initialized = false;
+const char kMax31855Types[] PROGMEM = "MAX31855|MAX6675";
 
-struct MAX31855_ResultStruct{
+bool max31855_initialized = false;
-    uint8_t ErrorCode;                  // Error Codes: 0 = No Error / 1 = TC open circuit / 2 = TC short to GND / 4 = TC short to VCC
+
-    float ProbeTemperature;             // Measured temperature of the 'hot' TC junction (probe temp)
+struct MAX31855_ResultStruct {
-    float ReferenceTemperature;         // Measured temperature of the 'cold' TC junction (reference temp)
+  uint8_t ErrorCode;                  // Error Codes: 0 = No Error / 1 = TC open circuit / 2 = TC short to GND / 4 = TC short to VCC
+  float ProbeTemperature;             // Measured temperature of the 'hot' TC junction (probe temp)
+  float ReferenceTemperature;         // Measured temperature of the 'cold' TC junction (reference temp)
 } MAX31855_Result;
 
-void MAX31855_Init(void){
+void MAX31855_Init(void) {
-    if(initialized)
+  if (PinUsed(GPIO_MAX31855CS) && PinUsed(GPIO_MAX31855CLK) && PinUsed(GPIO_MAX31855DO)) {
-        return;
 
     // Set GPIO modes for SW-SPI
     pinMode(Pin(GPIO_MAX31855CS), OUTPUT);
@@ -42,120 +49,122 @@ void MAX31855_Init(void){
     digitalWrite(Pin(GPIO_MAX31855CS), HIGH);
     digitalWrite(Pin(GPIO_MAX31855CLK), LOW);
 
-    initialized = true;
+    max31855_initialized = true;
-}
+  }
-
-/*
-*   MAX31855_GetResult(void)
-*   Acquires the raw data via SPI, checks for MAX31855 errors and fills result structure
-*/
-void MAX31855_GetResult(void){
-    // Controlled via SetOption94
-    if (Settings.flag4.max6675) {
-        int32_t RawData = MAX31855_ShiftIn(16);
-        int32_t temp = (RawData >> 3) & ((1 << 12) - 1);
-
-        /* Occasionally the sensor returns 0xfff, consider it an error */
-        if (temp == ((1 << 12) - 1))
-            return;
-
-        MAX31855_Result.ErrorCode = 0;
-        MAX31855_Result.ReferenceTemperature = NAN;
-        MAX31855_Result.ProbeTemperature = ConvertTemp(0.25 * temp);
-        return;
-    }
-    int32_t RawData = MAX31855_ShiftIn(32);
-    uint8_t probeerror = RawData & 0x7;
-
-    MAX31855_Result.ErrorCode = probeerror;
-    MAX31855_Result.ReferenceTemperature = MAX31855_GetReferenceTemperature(RawData);
-    if(probeerror)
-        MAX31855_Result.ProbeTemperature = NAN;     // Return NaN if MAX31855 reports an error
-    else
-        MAX31855_Result.ProbeTemperature = MAX31855_GetProbeTemperature(RawData);
-}
-
-
-/*
-*   MAX31855_GetProbeTemperature(int32_t RawData)
-*   Decodes and returns the temperature of TCs 'hot' junction from RawData
-*/
-float MAX31855_GetProbeTemperature(int32_t RawData){
-    if(RawData & 0x80000000)
-        RawData = (RawData >> 18) | 0xFFFFC000;     // Negative value - Drop lower 18 bits and extend to negative number
-    else
-        RawData >>= 18;                             // Positiv value - Drop lower 18 bits
-
-    float result = (RawData * 0.25);                // MAX31855 LSB resolution is 0.25°C for probe temperature
-
-    return ConvertTemp(result);                     // Check if we have to convert to Fahrenheit
-}
-
-/*
-*   MAX31855_GetReferenceTemperature(int32_t RawData)
-*   Decodes and returns the temperature of TCs 'cold' junction from RawData
-*/
-float MAX31855_GetReferenceTemperature(int32_t RawData){
-    if(RawData & 0x8000)
-        RawData = (RawData >> 4) | 0xFFFFF000;      // Negative value - Drop lower 4 bits and extend to negative number
-    else
-        RawData = (RawData >> 4) & 0x00000FFF;      // Positiv value - Drop lower 4 bits and mask out remaining bits (probe temp, error bit, etc.)
-
-    float result = (RawData * 0.0625);              // MAX31855 LSB resolution is 0.0625°C for reference temperature
-
-    return ConvertTemp(result);                     // Check if we have to convert to Fahrenheit
 }
 
 /*
 *   MAX31855_ShiftIn(uint8_t Length)
 *   Communicates with MAX31855 via SW-SPI and returns the raw data read from the chip
 */
-int32_t MAX31855_ShiftIn(uint8_t Length){
+int32_t MAX31855_ShiftIn(uint8_t Length) {
-    int32_t dataIn = 0;
+  int32_t dataIn = 0;
 
-    digitalWrite(Pin(GPIO_MAX31855CS), LOW);            // CS = LOW -> Start SPI communication
+  digitalWrite(Pin(GPIO_MAX31855CS), LOW);       // CS = LOW -> Start SPI communication
-    delayMicroseconds(1);                               // CS fall to output enable = max. 100ns
+  delayMicroseconds(1);                          // CS fall to output enable = max. 100ns
 
-    for (uint32_t i = 0; i < Length; i++)
+  for (uint32_t i = 0; i < Length; i++) {
-    {
-        digitalWrite(Pin(GPIO_MAX31855CLK), LOW);
-        delayMicroseconds(1);                           // CLK pulse width low = min. 100ns / CLK fall to output valid = max. 40ns
-        dataIn <<= 1;
-        if(digitalRead(Pin(GPIO_MAX31855DO)))
-            dataIn |= 1;
-        digitalWrite(Pin(GPIO_MAX31855CLK), HIGH);
-        delayMicroseconds(1);                           // CLK pulse width high = min. 100ns
-    }
-
-    digitalWrite(Pin(GPIO_MAX31855CS), HIGH);           // CS = HIGH -> End SPI communication
     digitalWrite(Pin(GPIO_MAX31855CLK), LOW);
-    return dataIn;
+    delayMicroseconds(1);                        // CLK pulse width low = min. 100ns / CLK fall to output valid = max. 40ns
+    dataIn <<= 1;
+    if (digitalRead(Pin(GPIO_MAX31855DO))) {
+      dataIn |= 1;
+    }
+    digitalWrite(Pin(GPIO_MAX31855CLK), HIGH);
+    delayMicroseconds(1);                        // CLK pulse width high = min. 100ns
+  }
+
+  digitalWrite(Pin(GPIO_MAX31855CS), HIGH);      // CS = HIGH -> End SPI communication
+  digitalWrite(Pin(GPIO_MAX31855CLK), LOW);
+  return dataIn;
 }
 
-void MAX31855_Show(bool Json){
+/*
-    char probetemp[33];
+*   MAX31855_GetProbeTemperature(int32_t RawData)
-    char referencetemp[33];
+*   Decodes and returns the temperature of TCs 'hot' junction from RawData
-    dtostrfd(MAX31855_Result.ProbeTemperature, Settings.flag2.temperature_resolution, probetemp);
+*/
-    dtostrfd(MAX31855_Result.ReferenceTemperature, Settings.flag2.temperature_resolution, referencetemp);
+float MAX31855_GetProbeTemperature(int32_t RawData) {
+  if (RawData & 0x80000000) {
+    RawData = (RawData >> 18) | 0xFFFFC000;      // Negative value - Drop lower 18 bits and extend to negative number
+  } else {
+    RawData >>= 18;                              // Positiv value - Drop lower 18 bits
+  }
+  float result = (RawData * 0.25);               // MAX31855 LSB resolution is 0.25°C for probe temperature
 
-    if(Json){
+  return ConvertTemp(result);                    // Check if we have to convert to Fahrenheit
-        ResponseAppend_P(PSTR(",\"MAX31855\":{\"" D_JSON_PROBETEMPERATURE "\":%s,\"" D_JSON_REFERENCETEMPERATURE "\":%s,\"" D_JSON_ERROR "\":%d}"), \
+}
-          probetemp, referencetemp, MAX31855_Result.ErrorCode);
+
+/*
+*   MAX31855_GetReferenceTemperature(int32_t RawData)
+*   Decodes and returns the temperature of TCs 'cold' junction from RawData
+*/
+float MAX31855_GetReferenceTemperature(int32_t RawData) {
+  if (RawData & 0x8000) {
+    RawData = (RawData >> 4) | 0xFFFFF000;       // Negative value - Drop lower 4 bits and extend to negative number
+  } else {
+    RawData = (RawData >> 4) & 0x00000FFF;       // Positiv value - Drop lower 4 bits and mask out remaining bits (probe temp, error bit, etc.)
+  }
+  float result = (RawData * 0.0625);             // MAX31855 LSB resolution is 0.0625°C for reference temperature
+
+  return ConvertTemp(result);                    // Check if we have to convert to Fahrenheit
+}
+
+/*
+*   MAX31855_GetResult(void)
+*   Acquires the raw data via SPI, checks for MAX31855 errors and fills result structure
+*/
+void MAX31855_GetResult(void) {
+  if (Settings.flag4.max6675) {                  // SetOption94 - Implement simpler MAX6675 protocol instead of MAX31855
+    int32_t RawData = MAX31855_ShiftIn(16);
+    int32_t temp = (RawData >> 3) & ((1 << 12) - 1);
+
+    /* Occasionally the sensor returns 0xfff, consider it an error */
+    if (temp == ((1 << 12) - 1)) { return; }
+
+    MAX31855_Result.ErrorCode = 0;
+    MAX31855_Result.ReferenceTemperature = NAN;
+    MAX31855_Result.ProbeTemperature = ConvertTemp(0.25 * temp);
+  } else {
+    int32_t RawData = MAX31855_ShiftIn(32);
+    uint8_t probeerror = RawData & 0x7;
+
+    MAX31855_Result.ErrorCode = probeerror;
+    MAX31855_Result.ReferenceTemperature = MAX31855_GetReferenceTemperature(RawData);
+    if (probeerror) {
+      MAX31855_Result.ProbeTemperature = NAN;    // Return NaN if MAX31855 reports an error
+    } else {
+      MAX31855_Result.ProbeTemperature = MAX31855_GetProbeTemperature(RawData);
+    }
+  }
+}
+
+void MAX31855_Show(bool Json) {
+  char probetemp[33];
+  char referencetemp[33];
+  dtostrfd(MAX31855_Result.ProbeTemperature, Settings.flag2.temperature_resolution, probetemp);
+  dtostrfd(MAX31855_Result.ReferenceTemperature, Settings.flag2.temperature_resolution, referencetemp);
+
+  char sensor_name[10];
+  GetTextIndexed(sensor_name, sizeof(sensor_name), Settings.flag4.max6675, kMax31855Types);
+
+  if (Json) {
+    ResponseAppend_P(PSTR(",\"%s\":{\"" D_JSON_PROBETEMPERATURE "\":%s,\"" D_JSON_REFERENCETEMPERATURE "\":%s,\"" D_JSON_ERROR "\":%d}"), \
+      sensor_name, probetemp, referencetemp, MAX31855_Result.ErrorCode);
 #ifdef USE_DOMOTICZ
-        if (0 == tele_period) {
+    if (0 == tele_period) {
-          DomoticzSensor(DZ_TEMP, probetemp);
+      DomoticzSensor(DZ_TEMP, probetemp);
-        }
+    }
 #endif  // USE_DOMOTICZ
 #ifdef USE_KNX
-        if (0 == tele_period) {
+    if (0 == tele_period) {
-          KnxSensor(KNX_TEMPERATURE, MAX31855_Result.ProbeTemperature);
+      KnxSensor(KNX_TEMPERATURE, MAX31855_Result.ProbeTemperature);
-        }
-#endif  // USE_KNX
-    } else {
-#ifdef USE_WEBSERVER
-        WSContentSend_PD(HTTP_SNS_TEMP, "MAX31855", probetemp, TempUnit());
-#endif  // USE_WEBSERVER
     }
+#endif  // USE_KNX
+#ifdef USE_WEBSERVER
+  } else {
+    WSContentSend_PD(HTTP_SNS_TEMP, sensor_name, probetemp, TempUnit());
+#endif  // USE_WEBSERVER
+  }
 }
 
 /*********************************************************************************************\
@@ -165,12 +174,12 @@ void MAX31855_Show(bool Json){
 bool Xsns39(uint8_t function)
 {
   bool result = false;
-  if(PinUsed(GPIO_MAX31855CS) && PinUsed(GPIO_MAX31855CLK) && PinUsed(GPIO_MAX31855DO)){
 
+  if (FUNC_INIT == function) {
+    MAX31855_Init();
+  }
+  else if (max31855_initialized) {
     switch (function) {
-      case FUNC_INIT:
-        MAX31855_Init();
-        break;
       case FUNC_EVERY_SECOND:
         MAX31855_GetResult();
         break;