Add support for Energy sensor (Denky)

Add support for Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers

RELEASENOTES.md

@@ -81,6 +81,6 @@ The following binary downloads have been compiled with ESP8266/Arduino library c
 - Add initial support for Telegram bot (#8619)
 - Add support for HP303B Temperature and Pressure sensor by Robert Jaakke (#8638)
 - Add rule trigger ``System#Init`` to allow early rule execution without wifi and mqtt initialized yet
-- Created Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers, need a adaptater. See dedicated full [blog](http://hallard.me/category/tinfo/) about French teleinformation stuff
+- Add support for Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers, need a adaptater. See dedicated full [blog](http://hallard.me/category/tinfo/) about French teleinformation stuff
-- Added Library to be used for decoding Teleinfo (French Metering Smart Meter)
+- Add Library to be used for decoding Teleinfo (French Metering Smart Meter)
 - Add basic support for ESP32 ethernet adding commands ``Wifi 0/1`` and ``Ethernet 0/1`` both default ON

tasmota/CHANGELOG.md

@@ -3,6 +3,9 @@
 ### 8.3.1.6 20200617
 
 - Add command ``Module2`` to configure fallback module on fast reboot (#8464)
+- Add support for Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers, need a adaptater. See dedicated full [blog](http://hallard.me/category/tinfo/) about French teleinformation stuff
+- Add Library to be used for decoding Teleinfo (French Metering Smart Meter)
+
 
 ### 8.3.1.5 20200616
 

tasmota/my_user_config.h

@@ -600,8 +600,6 @@
   #define USE_TASMOTA_SLAVE_FLASH_SPEED 57600      // Usually 57600 for 3.3V variants and 115200 for 5V variants
   #define USE_TASMOTA_SLAVE_SERIAL_SPEED 57600     // Depends on the sketch that is running on the Uno/Pro Mini
 //#define USE_OPENTHERM                            // Add support for OpenTherm (+15k code)
-#define USE_TELEINFO                               // Add support for Teleinfo via serial RX interface 
-  //#define USE_TELEINFO_STANDARD                    // Use standard mode (9600 bps) else it's historical mode (1200 bps)
 
 // -- Power monitoring sensors --------------------
 #define USE_ENERGY_MARGIN_DETECTION              // Add support for Energy Margin detection (+1k6 code)
@@ -625,6 +623,8 @@
   #define LE01MR_SPEED         9600              // LE-01MR modbus baudrate (default: 9600)
   #define LE01MR_ADDR          1                 // LE-01MR modbus address (default: 0x01)
 #define USE_BL0940                               // Add support for BL0940 Energy monitor as used in Blitzwolf SHP-10 (+1k6 code)
+//#define USE_TELEINFO                             // Add support for Teleinfo via serial RX interface (+5k2 code, +168 RAM + SmartMeter LinkedList Values RAM)
+//  #define USE_TELEINFO_STANDARD                  // Use standard mode (9600 bps) else it's historical mode (1200 bps)
 
 // -- Low level interface devices -----------------
 #define USE_DHT                                  // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor (1k6 code)

tasmota/tasmota_template.h

@@ -328,7 +328,7 @@ const char kSensorNames[] PROGMEM =
   D_SENSOR_AS3935 "|" D_SENSOR_PMS5003_TX "|"
   D_SENSOR_BOILER_OT_RX "|" D_SENSOR_BOILER_OT_TX "|"
   D_SENSOR_WINDMETER_SPEED "|"
-  D_SENSOR_BL0940_RX  "|"
+  D_SENSOR_BL0940_RX "|"
   D_SENSOR_TCP_TXD "|" D_SENSOR_TCP_RXD "|"
   D_SENSOR_TELEINFO_RX "|" D_SENSOR_TELEINFO_ENABLE
   ;
@@ -2264,10 +2264,8 @@ const mytmplt kModules[MAXMODULE] PROGMEM = {
     GPIO_LED1_INV,    // GPIO13 WiFi Blue Led - Link and Power status
     0, 0, 0, 0
   }
-
 };
 
-
 #endif  // ESP8266
 
 #ifdef ESP32

tasmota/tasmota_template_ESP32.h

@@ -622,20 +622,14 @@ typedef struct MYTMPLT {
 
 /********************************************************************************************/
 // Supported hardware modules
-enum SupportedModules {
+enum SupportedModules { WEMOS, ESP32_CAM_AITHINKER, MAXMODULE };
-  WEMOS, ESP32_CAM_AITHINKER, 
-  MAXMODULE};
 
 #define USER_MODULE        255
 
-const char kModuleNames[] PROGMEM =
+const char kModuleNames[] PROGMEM = "ESP32-DevKit|ESP32 Cam AiThinker";
-  "ESP32-DevKit|ESP32 Cam AiThinker";
 
 // Default module settings
-const uint8_t kModuleNiceList[MAXMODULE] PROGMEM = {
+const uint8_t kModuleNiceList[MAXMODULE] PROGMEM = { WEMOS, ESP32_CAM_AITHINKER };
-  WEMOS,
-  ESP32_CAM_AITHINKER
-};
 
 const mytmplt kModules PROGMEM =
 {                              // WEMOS - Espressif ESP32-DevKitC - Any ESP32 device like WeMos and NodeMCU hardware (ESP32)
@@ -690,7 +684,6 @@ const mytmplt kModules PROGMEM =
 
 \*********************************************************************************************/
 
-
 #endif  // ESP32
 
 #endif  // _TASMOTA_TEMPLATE_ESP32_H_

tools/decode-status.py

@@ -206,7 +206,7 @@ a_features = [[
     "USE_IAQ","USE_DISPLAY_SEVENSEG","USE_AS3935","USE_PING",
     "USE_WINDMETER","USE_OPENTHERM","USE_THERMOSTAT","USE_VEML6075",
     "USE_VEML7700","USE_MCP9808","USE_BL0940","USE_TELEGRAM",
-    "USE_HP303B","USE_TCP_BRIDGE","","",
+    "USE_HP303B","USE_TCP_BRIDGE","USE_TELEINFO","",
     "","","","",
     "","","","",
     "","","USE_ETHERNET","USE_WEBCAM"