diff --git a/homeassistant/components/fronius/const.py b/homeassistant/components/fronius/const.py index 273f1acab41..e8b2fa6c2e8 100644 --- a/homeassistant/components/fronius/const.py +++ b/homeassistant/components/fronius/const.py @@ -68,6 +68,167 @@ def get_inverter_status_message(code: StateType) -> InverterStatusCodeOption | N return _INVERTER_STATUS_CODES.get(code) # type: ignore[arg-type] +INVERTER_ERROR_CODES: Final[dict[int, str]] = { + 0: "no_error", + 102: "ac_voltage_too_high", + 103: "ac_voltage_too_low", + 105: "ac_frequency_too_high", + 106: "ac_frequency_too_low", + 107: "ac_grid_outside_permissible_limits", + 108: "stand_alone_operation_detected", + 112: "rcmu_error", + 240: "arc_detection_triggered", + 241: "arc_detection_triggered", + 242: "arc_detection_triggered", + 243: "arc_detection_triggered", + 301: "overcurrent_ac", + 302: "overcurrent_dc", + 303: "dc_module_over_temperature", + 304: "ac_module_over_temperature", + 305: "no_power_fed_in_despite_closed_relay", + 306: "pv_output_too_low_for_feeding_energy_into_the_grid", + 307: "low_pv_voltage_dc_input_voltage_too_low", + 308: "intermediate_circuit_voltage_too_high", + 309: "dc_input_voltage_mppt_1_too_high", + 311: "polarity_of_dc_strings_reversed", + 313: "dc_input_voltage_mppt_2_too_high", + 314: "current_sensor_calibration_timeout", + 315: "ac_current_sensor_error", + 316: "interrupt_check_fail", + 325: "overtemperature_in_connection_area", + 326: "fan_1_error", + 327: "fan_2_error", + 401: "no_communication_with_power_stage_set", + 406: "ac_module_temperature_sensor_faulty_l1", + 407: "ac_module_temperature_sensor_faulty_l2", + 408: "dc_component_measured_in_grid_too_high", + 412: "fixed_voltage_mode_out_of_range", + 415: "safety_cut_out_triggered", + 416: "no_communication_between_power_stage_and_control_system", + 417: "hardware_id_problem", + 419: "unique_id_conflict", + 420: "no_communication_with_hybrid_manager", + 421: "hid_range_error", + 425: "no_communication_with_power_stage_set", + 426: "possible_hardware_fault", + 427: "possible_hardware_fault", + 428: "possible_hardware_fault", + 431: "software_problem", + 436: "functional_incompatibility_between_pc_boards", + 437: "power_stage_set_problem", + 438: "functional_incompatibility_between_pc_boards", + 443: "intermediate_circuit_voltage_too_low_or_asymmetric", + 445: "compatibility_error_invalid_power_stage_configuration", + 447: "insulation_fault", + 448: "neutral_conductor_not_connected", + 450: "guard_cannot_be_found", + 451: "memory_error_detected", + 452: "communication", + 502: "insulation_error_on_solar_panels", + 509: "no_energy_fed_into_grid_past_24_hours", + 515: "no_communication_with_filter", + 516: "no_communication_with_storage_unit", + 517: "power_derating_due_to_high_temperature", + 518: "internal_dsp_malfunction", + 519: "no_communication_with_storage_unit", + 520: "no_energy_fed_by_mppt1_past_24_hours", + 522: "dc_low_string_1", + 523: "dc_low_string_2", + 558: "functional_incompatibility_between_pc_boards", + 559: "functional_incompatibility_between_pc_boards", + 560: "derating_caused_by_over_frequency", + 564: "functional_incompatibility_between_pc_boards", + 566: "arc_detector_switched_off", + 567: "grid_voltage_dependent_power_reduction_active", + 601: "can_bus_full", + 603: "ac_module_temperature_sensor_faulty_l3", + 604: "dc_module_temperature_sensor_faulty", + 607: "rcmu_error", + 608: "functional_incompatibility_between_pc_boards", + 701: "internal_processor_status", + 702: "internal_processor_status", + 703: "internal_processor_status", + 704: "internal_processor_status", + 705: "internal_processor_status", + 706: "internal_processor_status", + 707: "internal_processor_status", + 708: "internal_processor_status", + 709: "internal_processor_status", + 710: "internal_processor_status", + 711: "internal_processor_status", + 712: "internal_processor_status", + 713: "internal_processor_status", + 714: "internal_processor_status", + 715: "internal_processor_status", + 716: "internal_processor_status", + 721: "eeprom_reinitialised", + 722: "internal_processor_status", + 723: "internal_processor_status", + 724: "internal_processor_status", + 725: "internal_processor_status", + 726: "internal_processor_status", + 727: "internal_processor_status", + 728: "internal_processor_status", + 729: "internal_processor_status", + 730: "internal_processor_status", + 731: "initialisation_error_usb_flash_drive_not_supported", + 732: "initialisation_error_usb_stick_over_current", + 733: "no_usb_flash_drive_connected", + 734: "update_file_not_recognised_or_missing", + 735: "update_file_does_not_match_device", + 736: "write_or_read_error_occurred", + 737: "file_could_not_be_opened", + 738: "log_file_cannot_be_saved", + 740: "initialisation_error_file_system_error_on_usb", + 741: "error_during_logging_data_recording", + 743: "error_during_update_process", + 745: "update_file_corrupt", + 746: "error_during_update_process", + 751: "time_lost", + 752: "real_time_clock_communication_error", + 753: "real_time_clock_in_emergency_mode", + 754: "internal_processor_status", + 755: "internal_processor_status", + 757: "real_time_clock_hardware_error", + 758: "real_time_clock_in_emergency_mode", + 760: "internal_hardware_error", + 761: "internal_processor_status", + 762: "internal_processor_status", + 763: "internal_processor_status", + 764: "internal_processor_status", + 765: "internal_processor_status", + 766: "emergency_power_derating_activated", + 767: "internal_processor_status", + 768: "different_power_limitation_in_hardware_modules", + 772: "storage_unit_not_available", + 773: "software_update_invalid_country_setup", + 775: "pmc_power_stage_set_not_available", + 776: "invalid_device_type", + 781: "internal_processor_status", + 782: "internal_processor_status", + 783: "internal_processor_status", + 784: "internal_processor_status", + 785: "internal_processor_status", + 786: "internal_processor_status", + 787: "internal_processor_status", + 788: "internal_processor_status", + 789: "internal_processor_status", + 790: "internal_processor_status", + 791: "internal_processor_status", + 792: "internal_processor_status", + 793: "internal_processor_status", + 794: "internal_processor_status", + 1001: "insulation_measurement_triggered", + 1024: "inverter_settings_changed_restart_required", + 1030: "wired_shut_down_triggered", + 1036: "grid_frequency_exceeded_limit_reconnecting", + 1112: "mains_voltage_dependent_power_reduction", + 1175: "too_little_dc_power_for_feed_in_operation", + 1196: "inverter_required_setup_values_not_received", + 65000: "dc_connection_inverter_battery_interrupted", +} + + class MeterLocationCodeOption(StrEnum): """Meter location codes for Fronius meters.""" diff --git a/homeassistant/components/fronius/sensor.py b/homeassistant/components/fronius/sensor.py index 95c5df269e4..03f666ffafd 100644 --- a/homeassistant/components/fronius/sensor.py +++ b/homeassistant/components/fronius/sensor.py @@ -33,6 +33,7 @@ from homeassistant.helpers.update_coordinator import CoordinatorEntity from .const import ( DOMAIN, + INVERTER_ERROR_CODES, SOLAR_NET_DISCOVERY_NEW, InverterStatusCodeOption, MeterLocationCodeOption, @@ -205,6 +206,15 @@ INVERTER_ENTITY_DESCRIPTIONS: list[FroniusSensorEntityDescription] = [ FroniusSensorEntityDescription( key="error_code", entity_category=EntityCategory.DIAGNOSTIC, + entity_registry_enabled_default=False, + ), + FroniusSensorEntityDescription( + key="error_message", + response_key="error_code", + entity_category=EntityCategory.DIAGNOSTIC, + device_class=SensorDeviceClass.ENUM, + options=list(dict.fromkeys(INVERTER_ERROR_CODES.values())), + value_fn=INVERTER_ERROR_CODES.get, # type: ignore[arg-type] ), FroniusSensorEntityDescription( key="status_code", diff --git a/homeassistant/components/fronius/strings.json b/homeassistant/components/fronius/strings.json index e2740c76696..b77f6fec83c 100644 --- a/homeassistant/components/fronius/strings.json +++ b/homeassistant/components/fronius/strings.json @@ -73,6 +73,107 @@ "error_code": { "name": "Error code" }, + "error_message": { + "name": "Error message", + "state": { + "no_error": "No error", + "ac_voltage_too_high": "AC voltage too high", + "ac_voltage_too_low": "AC voltage too low", + "ac_frequency_too_high": "AC frequency too high", + "ac_frequency_too_low": "AC frequency too low", + "ac_grid_outside_permissible_limits": "AC grid outside the permissible limits", + "stand_alone_operation_detected": "Stand alone operation detected", + "rcmu_error": "RCMU error", + "arc_detection_triggered": "Arc detection triggered", + "overcurrent_ac": "Overcurrent (AC)", + "overcurrent_dc": "Overcurrent (DC)", + "dc_module_over_temperature": "DC module over temperature", + "ac_module_over_temperature": "AC module over temperature", + "no_power_fed_in_despite_closed_relay": "No power being fed in, despite closed relay", + "pv_output_too_low_for_feeding_energy_into_the_grid": "PV output too low for feeding energy into the grid", + "low_pv_voltage_dc_input_voltage_too_low": "Low PV voltage - DC input voltage too low for feeding energy into the grid", + "intermediate_circuit_voltage_too_high": "Intermediate circuit voltage too high", + "dc_input_voltage_mppt_1_too_high": "DC input voltage MPPT 1 too high", + "polarity_of_dc_strings_reversed": "Polarity of DC strings reversed", + "dc_input_voltage_mppt_2_too_high": "DC input voltage MPPT 2 too high", + "current_sensor_calibration_timeout": "Current sensor calibration timeout", + "ac_current_sensor_error": "AC current sensor error", + "interrupt_check_fail": "Interrupt Check fail", + "overtemperature_in_connection_area": "Overtemperature in the connection area", + "fan_1_error": "Fan 1 error", + "fan_2_error": "Fan 2 error", + "no_communication_with_power_stage_set": "No communication with the power stage set possible", + "ac_module_temperature_sensor_faulty_l1": "AC module temperature sensor faulty (L1)", + "ac_module_temperature_sensor_faulty_l2": "AC module temperature sensor faulty (L2)", + "dc_component_measured_in_grid_too_high": "DC component measured in the grid too high", + "fixed_voltage_mode_out_of_range": "Fixed voltage mode has been selected instead of MPP voltage mode and the fixed voltage has been set to too low or too high a value", + "safety_cut_out_triggered": "Safety cut out via option card or RECERBO has triggered", + "no_communication_between_power_stage_and_control_system": "No communication possible between power stage set and control system", + "hardware_id_problem": "Hardware ID problem", + "unique_id_conflict": "Unique ID conflict", + "no_communication_with_hybrid_manager": "No communication possible with the Hybrid manager", + "hid_range_error": "HID range error", + "possible_hardware_fault": "Possible hardware fault", + "software_problem": "Software problem", + "functional_incompatibility_between_pc_boards": "Functional incompatibility (one or more PC boards in the inverter are not compatible with each other, e.g. after a PC board has been replaced)", + "power_stage_set_problem": "Power stage set problem", + "intermediate_circuit_voltage_too_low_or_asymmetric": "Intermediate circuit voltage too low or asymmetric", + "compatibility_error_invalid_power_stage_configuration": "Compatibility error (e.g. due to replacement of a PC board) - invalid power stage set configuration", + "insulation_fault": "Insulation fault", + "neutral_conductor_not_connected": "Neutral conductor not connected", + "guard_cannot_be_found": "Guard cannot be found", + "memory_error_detected": "Memory error detected", + "communication": "Communication error", + "insulation_error_on_solar_panels": "Insulation error on the solar panels", + "no_energy_fed_into_grid_past_24_hours": "No energy fed into the grid in the past 24 hours", + "no_communication_with_filter": "No communication with filter possible", + "no_communication_with_storage_unit": "No communication possible with the storage unit", + "power_derating_due_to_high_temperature": "Power derating caused by too high a temperature", + "internal_dsp_malfunction": "Internal DSP malfunction", + "no_energy_fed_by_mppt1_past_24_hours": "No energy fed into the grid by MPPT1 in the past 24 hours", + "dc_low_string_1": "DC low string 1", + "dc_low_string_2": "DC low string 2", + "derating_caused_by_over_frequency": "Derating caused by over-frequency", + "arc_detector_switched_off": "Arc detector switched off (e.g. during external arc monitoring)", + "grid_voltage_dependent_power_reduction_active": "Grid Voltage Dependent Power Reduction is active", + "can_bus_full": "CAN bus is full", + "ac_module_temperature_sensor_faulty_l3": "AC module temperature sensor faulty (L3)", + "dc_module_temperature_sensor_faulty": "DC module temperature sensor faulty", + "internal_processor_status": "Warning about the internal processor status. See status code for more information", + "eeprom_reinitialised": "EEPROM has been re-initialised", + "initialisation_error_usb_flash_drive_not_supported": "Initialisation error – USB flash drive is not supported", + "initialisation_error_usb_stick_over_current": "Initialisation error – Over current on USB stick", + "no_usb_flash_drive_connected": "No USB flash drive connected", + "update_file_not_recognised_or_missing": "Update file not recognised or not present", + "update_file_does_not_match_device": "Update file does not match the device, update file too old", + "write_or_read_error_occurred": "Write or read error occurred", + "file_could_not_be_opened": "File could not be opened", + "log_file_cannot_be_saved": "Log file cannot be saved (e.g. USB flash drive is write protected or full)", + "initialisation_error_file_system_error_on_usb": "Initialisation error in file system on USB flash drive", + "error_during_logging_data_recording": "Error during recording of logging data", + "error_during_update_process": "Error occurred during update process", + "update_file_corrupt": "Update file corrupt", + "time_lost": "Time lost", + "real_time_clock_communication_error": "Real Time Clock module communication error", + "real_time_clock_in_emergency_mode": "Internal error: Real Time Clock module is in emergency mode", + "real_time_clock_hardware_error": "Hardware error in the Real Time Clock module", + "internal_hardware_error": "Internal hardware error", + "emergency_power_derating_activated": "Emergency power derating activated", + "different_power_limitation_in_hardware_modules": "Different power limitation in the hardware modules", + "storage_unit_not_available": "Storage unit not available", + "software_update_invalid_country_setup": "Software update group 0 (invalid country setup)", + "pmc_power_stage_set_not_available": "PMC power stage set not available", + "invalid_device_type": "Invalid device type", + "insulation_measurement_triggered": "Insulation measurement triggered", + "inverter_settings_changed_restart_required": "Inverter settings have been changed, inverter restart required", + "wired_shut_down_triggered": "Wired shut down triggered", + "grid_frequency_exceeded_limit_reconnecting": "The grid frequency has exceeded a limit value when reconnecting", + "mains_voltage_dependent_power_reduction": "Mains voltage-dependent power reduction", + "too_little_dc_power_for_feed_in_operation": "Too little DC power for feed-in operation", + "inverter_required_setup_values_not_received": "Inverter required setup values could not be received", + "dc_connection_inverter_battery_interrupted": "DC connection between inverter and battery interrupted" + } + }, "status_code": { "name": "Status code" }, diff --git a/tests/components/fronius/snapshots/test_sensor.ambr b/tests/components/fronius/snapshots/test_sensor.ambr index 8f8c9d919fc..81770893273 100644 --- a/tests/components/fronius/snapshots/test_sensor.ambr +++ b/tests/components/fronius/snapshots/test_sensor.ambr @@ -402,6 +402,250 @@ 'state': '0', }) # --- +# name: test_gen24[sensor.inverter_name_error_message-entry] + EntityRegistryEntrySnapshot({ + 'aliases': set({ + }), + 'area_id': None, + 'capabilities': dict({ + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'config_entry_id': , + 'device_class': None, + 'device_id': , + 'disabled_by': None, + 'domain': 'sensor', + 'entity_category': , + 'entity_id': 'sensor.inverter_name_error_message', + 'has_entity_name': True, + 'hidden_by': None, + 'icon': None, + 'id': , + 'labels': set({ + }), + 'name': None, + 'options': dict({ + }), + 'original_device_class': , + 'original_icon': None, + 'original_name': 'Error message', + 'platform': 'fronius', + 'previous_unique_id': None, + 'supported_features': 0, + 'translation_key': 'error_message', + 'unique_id': '12345678-error_message', + 'unit_of_measurement': None, + }) +# --- +# name: test_gen24[sensor.inverter_name_error_message-state] + StateSnapshot({ + 'attributes': ReadOnlyDict({ + 'device_class': 'enum', + 'friendly_name': 'Inverter name Error message', + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'context': , + 'entity_id': 'sensor.inverter_name_error_message', + 'last_changed': , + 'last_reported': , + 'last_updated': , + 'state': 'no_error', + }) +# --- # name: test_gen24[sensor.inverter_name_frequency-entry] EntityRegistryEntrySnapshot({ 'aliases': set({ @@ -3653,6 +3897,250 @@ 'state': '0', }) # --- +# name: test_gen24_storage[sensor.gen24_storage_error_message-entry] + EntityRegistryEntrySnapshot({ + 'aliases': set({ + }), + 'area_id': None, + 'capabilities': dict({ + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'config_entry_id': , + 'device_class': None, + 'device_id': , + 'disabled_by': None, + 'domain': 'sensor', + 'entity_category': , + 'entity_id': 'sensor.gen24_storage_error_message', + 'has_entity_name': True, + 'hidden_by': None, + 'icon': None, + 'id': , + 'labels': set({ + }), + 'name': None, + 'options': dict({ + }), + 'original_device_class': , + 'original_icon': None, + 'original_name': 'Error message', + 'platform': 'fronius', + 'previous_unique_id': None, + 'supported_features': 0, + 'translation_key': 'error_message', + 'unique_id': '12345678-error_message', + 'unit_of_measurement': None, + }) +# --- +# name: test_gen24_storage[sensor.gen24_storage_error_message-state] + StateSnapshot({ + 'attributes': ReadOnlyDict({ + 'device_class': 'enum', + 'friendly_name': 'Gen24 Storage Error message', + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'context': , + 'entity_id': 'sensor.gen24_storage_error_message', + 'last_changed': , + 'last_reported': , + 'last_updated': , + 'state': 'no_error', + }) +# --- # name: test_gen24_storage[sensor.gen24_storage_frequency-entry] EntityRegistryEntrySnapshot({ 'aliases': set({ @@ -7022,6 +7510,250 @@ 'state': '0', }) # --- +# name: test_primo_s0[sensor.primo_3_0_1_error_message-entry] + EntityRegistryEntrySnapshot({ + 'aliases': set({ + }), + 'area_id': None, + 'capabilities': dict({ + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'config_entry_id': , + 'device_class': None, + 'device_id': , + 'disabled_by': None, + 'domain': 'sensor', + 'entity_category': , + 'entity_id': 'sensor.primo_3_0_1_error_message', + 'has_entity_name': True, + 'hidden_by': None, + 'icon': None, + 'id': , + 'labels': set({ + }), + 'name': None, + 'options': dict({ + }), + 'original_device_class': , + 'original_icon': None, + 'original_name': 'Error message', + 'platform': 'fronius', + 'previous_unique_id': None, + 'supported_features': 0, + 'translation_key': 'error_message', + 'unique_id': '234567-error_message', + 'unit_of_measurement': None, + }) +# --- +# name: test_primo_s0[sensor.primo_3_0_1_error_message-state] + StateSnapshot({ + 'attributes': ReadOnlyDict({ + 'device_class': 'enum', + 'friendly_name': 'Primo 3.0-1 Error message', + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'context': , + 'entity_id': 'sensor.primo_3_0_1_error_message', + 'last_changed': , + 'last_reported': , + 'last_updated': , + 'state': 'no_error', + }) +# --- # name: test_primo_s0[sensor.primo_3_0_1_frequency-entry] EntityRegistryEntrySnapshot({ 'aliases': set({ @@ -7733,6 +8465,250 @@ 'state': '0', }) # --- +# name: test_primo_s0[sensor.primo_5_0_1_error_message-entry] + EntityRegistryEntrySnapshot({ + 'aliases': set({ + }), + 'area_id': None, + 'capabilities': dict({ + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'config_entry_id': , + 'device_class': None, + 'device_id': , + 'disabled_by': None, + 'domain': 'sensor', + 'entity_category': , + 'entity_id': 'sensor.primo_5_0_1_error_message', + 'has_entity_name': True, + 'hidden_by': None, + 'icon': None, + 'id': , + 'labels': set({ + }), + 'name': None, + 'options': dict({ + }), + 'original_device_class': , + 'original_icon': None, + 'original_name': 'Error message', + 'platform': 'fronius', + 'previous_unique_id': None, + 'supported_features': 0, + 'translation_key': 'error_message', + 'unique_id': '123456-error_message', + 'unit_of_measurement': None, + }) +# --- +# name: test_primo_s0[sensor.primo_5_0_1_error_message-state] + StateSnapshot({ + 'attributes': ReadOnlyDict({ + 'device_class': 'enum', + 'friendly_name': 'Primo 5.0-1 Error message', + 'options': list([ + 'no_error', + 'ac_voltage_too_high', + 'ac_voltage_too_low', + 'ac_frequency_too_high', + 'ac_frequency_too_low', + 'ac_grid_outside_permissible_limits', + 'stand_alone_operation_detected', + 'rcmu_error', + 'arc_detection_triggered', + 'overcurrent_ac', + 'overcurrent_dc', + 'dc_module_over_temperature', + 'ac_module_over_temperature', + 'no_power_fed_in_despite_closed_relay', + 'pv_output_too_low_for_feeding_energy_into_the_grid', + 'low_pv_voltage_dc_input_voltage_too_low', + 'intermediate_circuit_voltage_too_high', + 'dc_input_voltage_mppt_1_too_high', + 'polarity_of_dc_strings_reversed', + 'dc_input_voltage_mppt_2_too_high', + 'current_sensor_calibration_timeout', + 'ac_current_sensor_error', + 'interrupt_check_fail', + 'overtemperature_in_connection_area', + 'fan_1_error', + 'fan_2_error', + 'no_communication_with_power_stage_set', + 'ac_module_temperature_sensor_faulty_l1', + 'ac_module_temperature_sensor_faulty_l2', + 'dc_component_measured_in_grid_too_high', + 'fixed_voltage_mode_out_of_range', + 'safety_cut_out_triggered', + 'no_communication_between_power_stage_and_control_system', + 'hardware_id_problem', + 'unique_id_conflict', + 'no_communication_with_hybrid_manager', + 'hid_range_error', + 'possible_hardware_fault', + 'software_problem', + 'functional_incompatibility_between_pc_boards', + 'power_stage_set_problem', + 'intermediate_circuit_voltage_too_low_or_asymmetric', + 'compatibility_error_invalid_power_stage_configuration', + 'insulation_fault', + 'neutral_conductor_not_connected', + 'guard_cannot_be_found', + 'memory_error_detected', + 'communication', + 'insulation_error_on_solar_panels', + 'no_energy_fed_into_grid_past_24_hours', + 'no_communication_with_filter', + 'no_communication_with_storage_unit', + 'power_derating_due_to_high_temperature', + 'internal_dsp_malfunction', + 'no_energy_fed_by_mppt1_past_24_hours', + 'dc_low_string_1', + 'dc_low_string_2', + 'derating_caused_by_over_frequency', + 'arc_detector_switched_off', + 'grid_voltage_dependent_power_reduction_active', + 'can_bus_full', + 'ac_module_temperature_sensor_faulty_l3', + 'dc_module_temperature_sensor_faulty', + 'internal_processor_status', + 'eeprom_reinitialised', + 'initialisation_error_usb_flash_drive_not_supported', + 'initialisation_error_usb_stick_over_current', + 'no_usb_flash_drive_connected', + 'update_file_not_recognised_or_missing', + 'update_file_does_not_match_device', + 'write_or_read_error_occurred', + 'file_could_not_be_opened', + 'log_file_cannot_be_saved', + 'initialisation_error_file_system_error_on_usb', + 'error_during_logging_data_recording', + 'error_during_update_process', + 'update_file_corrupt', + 'time_lost', + 'real_time_clock_communication_error', + 'real_time_clock_in_emergency_mode', + 'real_time_clock_hardware_error', + 'internal_hardware_error', + 'emergency_power_derating_activated', + 'different_power_limitation_in_hardware_modules', + 'storage_unit_not_available', + 'software_update_invalid_country_setup', + 'pmc_power_stage_set_not_available', + 'invalid_device_type', + 'insulation_measurement_triggered', + 'inverter_settings_changed_restart_required', + 'wired_shut_down_triggered', + 'grid_frequency_exceeded_limit_reconnecting', + 'mains_voltage_dependent_power_reduction', + 'too_little_dc_power_for_feed_in_operation', + 'inverter_required_setup_values_not_received', + 'dc_connection_inverter_battery_interrupted', + ]), + }), + 'context': , + 'entity_id': 'sensor.primo_5_0_1_error_message', + 'last_changed': , + 'last_reported': , + 'last_updated': , + 'state': 'no_error', + }) +# --- # name: test_primo_s0[sensor.primo_5_0_1_frequency-entry] EntityRegistryEntrySnapshot({ 'aliases': set({ diff --git a/tests/components/fronius/test_sensor.py b/tests/components/fronius/test_sensor.py index b5d051d56ca..63f36705c8f 100644 --- a/tests/components/fronius/test_sensor.py +++ b/tests/components/fronius/test_sensor.py @@ -36,7 +36,7 @@ async def test_symo_inverter( mock_responses(aioclient_mock, night=True) await setup_fronius_integration(hass) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 58 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 59 assert_state("sensor.symo_20_dc_current", 0) assert_state("sensor.symo_20_energy_day", 10828) assert_state("sensor.symo_20_total_energy", 44186900) @@ -49,7 +49,7 @@ async def test_symo_inverter( freezer.tick(FroniusInverterUpdateCoordinator.default_interval) async_fire_time_changed(hass) await hass.async_block_till_done() - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 64 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 65 # 4 additional AC entities assert_state("sensor.symo_20_dc_current", 2.19) assert_state("sensor.symo_20_energy_day", 1113) @@ -108,7 +108,7 @@ async def test_symo_meter( mock_responses(aioclient_mock) await setup_fronius_integration(hass) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 64 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 65 # states are rounded to 4 decimals assert_state("sensor.smart_meter_63a_current_phase_1", 7.755) assert_state("sensor.smart_meter_63a_current_phase_2", 6.68) @@ -205,7 +205,7 @@ async def test_symo_power_flow( mock_responses(aioclient_mock, night=True) await setup_fronius_integration(hass) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 58 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 59 # states are rounded to 4 decimals assert_state("sensor.solarnet_energy_day", 10828) assert_state("sensor.solarnet_total_energy", 44186900) @@ -223,7 +223,7 @@ async def test_symo_power_flow( async_fire_time_changed(hass) await hass.async_block_till_done() # 54 because power_flow `rel_SelfConsumption` and `P_PV` is not `null` anymore - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 60 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 61 assert_state("sensor.solarnet_energy_day", 1101.7001) assert_state("sensor.solarnet_total_energy", 44188000) assert_state("sensor.solarnet_energy_year", 25508788) @@ -242,7 +242,7 @@ async def test_symo_power_flow( freezer.tick(FroniusPowerFlowUpdateCoordinator.default_interval) async_fire_time_changed(hass) await hass.async_block_till_done() - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 60 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 61 assert_state("sensor.solarnet_energy_day", 10828) assert_state("sensor.solarnet_total_energy", 44186900) assert_state("sensor.solarnet_energy_year", 25507686) @@ -271,7 +271,7 @@ async def test_gen24( mock_responses(aioclient_mock, fixture_set="gen24") config_entry = await setup_fronius_integration(hass, is_logger=False) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 58 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 59 await snapshot_platform(hass, entity_registry, snapshot, config_entry.entry_id) assert_state("sensor.inverter_name_total_energy", 1530193.42) @@ -313,7 +313,7 @@ async def test_gen24_storage( hass, is_logger=False, unique_id="12345678" ) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 72 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 73 await snapshot_platform(hass, entity_registry, snapshot, config_entry.entry_id) # Devices @@ -367,7 +367,7 @@ async def test_primo_s0( mock_responses(aioclient_mock, fixture_set="primo_s0", inverter_ids=[1, 2]) config_entry = await setup_fronius_integration(hass, is_logger=True) - assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 47 + assert len(hass.states.async_all(domain_filter=SENSOR_DOMAIN)) == 49 await snapshot_platform(hass, entity_registry, snapshot, config_entry.entry_id) # Devices