From c2d567b80e51767d7c2b25aee4ef1d38173c13b9 Mon Sep 17 00:00:00 2001 From: Achilleas Pipinellis Date: Wed, 27 Oct 2021 13:49:55 +0200 Subject: [PATCH] Refactor the SPI and ums info for the ODROID-N2+ (#20007) --- .../_includes/common-tasks/flashing_n2_otg.md | 41 +++++++++++-------- 1 file changed, 24 insertions(+), 17 deletions(-) diff --git a/source/_includes/common-tasks/flashing_n2_otg.md b/source/_includes/common-tasks/flashing_n2_otg.md index 380f7de6d14..3cf25919146 100644 --- a/source/_includes/common-tasks/flashing_n2_otg.md +++ b/source/_includes/common-tasks/flashing_n2_otg.md @@ -14,34 +14,41 @@ To flash your eMMC using Petitboot and OTG-USB, you will need the following item #### Enabling SPI boot mode -Remove the case of your ODROID-N2+ +To enable the SPI boot mode: -![Photo of the removed case](/images/hassio/screenshots/case-removed.jpg) +1. Power off the ODROID-N2+ by unplugging the power cable. +1. Remove the case. -Next, locate the toggle for boot mode and switch it from MMC to SPI. + ![Photo of the removed case](/images/hassio/screenshots/case-removed.jpg) -![Photo of the SPI toggle switch](/images/hassio/screenshots/toggle_spi.jpg) +1. Locate the toggle for boot mode and switch it from MMC to SPI. -Connect a USB keyboard and HDMI connected monitor to your ODROID-N2+, and then connect power. + ![Photo of the SPI toggle switch](/images/hassio/screenshots/toggle_spi.jpg) + +1. Connect the ODROID-N2+ directly to your computer via the USB-OTG port located on the front of the board. +1. Connect a USB keyboard and a monitor (using HDMI) to your ODROID-N2+. +1. Plug in the power cable to power on the ODROID-N2+. #### Enabling USB drive mode -The ODROID-N2+ will now boot into a terminal. Select `Exit to shell` from the menu. +After The ODROID-N2+ is set to SPI boot mode and powered on, it boots into a terminal. To enable the USB drive mode: -![Exit to shell](/images/hassio/screenshots/exit-shell.png) +1. Select `Exit to shell` from the menu. -Use the following command at the console to confirm the storage device node: + ![Exit to shell](/images/hassio/screenshots/exit-shell.png) -```bash -ls /dev/mmc* -``` +1. Use the following command at the console to confirm the storage device node: -Set the storage device on the ODROID-N2+ as a mass storage device using `ums` (USB Mass storage mode) -This will configure the ODROID-N2+ and OTG to act as a memory card reader. + ```bash + ls /dev/mmc* + ``` -```bash -ums /dev/mmcblk0 -``` +1. Set the storage device on the ODROID-N2+ as a mass storage device using the `ums` command (USB Mass storage mode). +This will configure the ODROID-N2+ and OTG to act as a memory card reader: + + ```bash + ums /dev/mmcblk0 + ``` #### Flashing Home Assistant @@ -51,4 +58,4 @@ When the flash process is complete, disconnect the ODROID-N2+ from your PC and r Once it is back in its case, connect your ODROID-N2+ to your network with an Ethernet cable and plug in power. -If your router supports mDNS, you will be able to reach your installation on `http://homeassistant.local:8123`. If your network doesn’t support mDNS, you’ll have to use the IP address of your ODROID-N2+ instead of `homeassistant.local`. For example, `http://192.168.0.9:8123`. You should be able to find the IP address of your ODROID-N2+ from the admin interface of your router. \ No newline at end of file +If your router supports mDNS, you will be able to reach your installation on `http://homeassistant.local:8123`. If your network doesn’t support mDNS, you’ll have to use the IP address of your ODROID-N2+ instead of `homeassistant.local`. For example, `http://192.168.0.9:8123`. You should be able to find the IP address of your ODROID-N2+ from the admin interface of your router.