Remove deprecated Bosch BMP280 Environmental Sensor integration (#21819)

CODEOWNERS

@@ -65,7 +65,6 @@ source/_integrations/blebox.markdown @bbx-a @bbx-jp
 source/_integrations/blink.markdown @fronzbot
 source/_integrations/blueprint.markdown @home-assistant/core
 source/_integrations/bluesound.markdown @thrawnarn
-source/_integrations/bmp280.markdown @belidzs
 source/_integrations/bmw_connected_drive.markdown @gerard33 @rikroe
 source/_integrations/bond.markdown @bdraco @prystupa @joshs85
 source/_integrations/bosch_shc.markdown @tschamm

source/_integrations/bmp280.markdown

@@ -1,60 +0,0 @@
----
-title: Bosch BMP280 Environmental Sensor
-description: Instructions on how to integrate a BMP280 sensor into Home Assistant.
-ha_release: 0.108
-ha_category:
-  - DIY
-ha_iot_class: Local Polling
-ha_quality_scale: silver
-ha_code_owners:
-  - '@belidzs'
-ha_domain: bmp280
-ha_codeowners:
-  - '@belidzs'
-ha_platforms:
-  - sensor
----
-
-<div class='note warning'>
-
-This integration is deprecated and will be removed in Home Assistant Core 2022.4.
-
-For more information see: [Architectural Decision Record 0019](https://github.com/home-assistant/architecture/blob/master/adr/0019-GPIO.md).
-
-</div>
-
-The `bmp280` sensor platform allows you to read temperature and pressure values of a [Bosch BMP280 Environmental sensor](https://www.bosch-sensortec.com/products/environmental-sensors/pressure-sensors/bmp280/) connected via [I2C](https://en.wikipedia.org/wiki/I²C) bus (SDA, SCL pins).
-
-This integration has been tested on a Raspberry Pi 4B, but it should work on any device which is supported by [CircuitPython](https://circuitpython.org/).
-
-## Configuration
-
-To use a BMP280 sensor in your installation, you have to enable I2C on your host device then configure the integration using the following example:
-
-```yaml
-sensor:
-  - platform: bmp280
-    i2c_address: 0x77
-```
-
-{% configuration %}
-name:
-  description: The name of the sensor.
-  required: false
-  default: BMP280
-  type: string
-i2c_address:
-  description: I2C address of the sensor. It is either 0x76 or 0x77, depending on your actual wiring configuration.
-  required: true
-  type: integer
-{% endconfiguration %}
-
-## Setting up the I2C interface on the host device
-
-To get more information on how to set up the I2C interface on your Raspberry Pi, please refer to the [BME680 sensor integration](/integrations/bme680/#directions-for-installing-smbus-support-on-raspberry-pi).
-
-## Choosing the appropriate I2C address
-
-Please note that the I2C address of this device depends on the state of the `SDO` pin. If it is pulled down (to the `GND` rail) it will be `0x76`, if it's pulled up (to the `VCC` rail) it will be `0x77`.
-
-If you leave it floating then the address will be unpredictable or even worse, it can change over time. So it is recommended to hook up this pin to either the positive or the negative rail of your host device.

source/_redirects

@@ -2373,6 +2373,7 @@
 /components/sensor.sensehat /more-info/removed-integration 301
 /integrations/sensehat /more-info/removed-integration 301
 /integrations/pi4ioe5v9xxxx /more-info/removed-integration 301
+/integrations/bmp280 /more-info/removed-integration 301
 /components/mcp23017 /more-info/removed-integration 301
 /integrations/mcp23017 /more-info/removed-integration 301
 /components/rpi_rf /more-info/removed-integration 301