diff --git a/source/_includes/common-tasks/flashing_n2_otg.md b/source/_includes/common-tasks/flashing_n2_otg.md
index f4cb0d8aa49..98c768e4a71 100644
--- a/source/_includes/common-tasks/flashing_n2_otg.md
+++ b/source/_includes/common-tasks/flashing_n2_otg.md
@@ -11,6 +11,7 @@ To flash your eMMC using Petitboot and OTG-USB, you will need the following item
 - HDMI cable and monitor
 - USB keyboard
 - USB 2.0 to micro-USB cable
+- If your board came in a Home Assistant Blue: No.2 hex key to open the case
 
 #### Enabling SPI boot mode
 
@@ -45,13 +46,13 @@ You can safely ignore this message and proceed with the installation
 
 </div>
 
-2. Use the following command at the console to confirm the storage device node:
+1. Use the following command at the console to confirm the storage device node:
 
    ```bash
    ls /dev/mmc*
    ```
 
-3. Set the storage device on the ODROID-N2+ as a mass storage device using the `ums` command (USB Mass storage mode).
+1. Set the storage device on the ODROID-N2+ as a mass storage device using the `ums` command (USB Mass storage mode).
 This will configure the ODROID-N2+ and OTG to act as a memory card reader:
 
    ```bash
@@ -60,10 +61,19 @@ This will configure the ODROID-N2+ and OTG to act as a memory card reader:
 
 #### Flashing Home Assistant
 
-Connect the ODROID-N2+ to your PC via the micro-USB port at the front of the ODROID-N2+. When the ODROID-N2 is recognized as a USB connected storage device, you can flash the eMMC with [Etcher](https://www.balena.io/etcher/) using the latest stable version of Home Assistant OS for the [ODROID-N2+](https://github.com/home-assistant/operating-system/releases/download/{{site.data.version_data.hassos['odroid-n2']}}/haos_odroid-n2-{{site.data.version_data.hassos['odroid-n2']}}.img.xz) (haos_odroid-n2-{{site.data.version_data.hassos['odroid-n2']}}.img.xz).
+1. Connect the ODROID-N2+ to your PC via the micro-USB port at the front of the ODROID-N2+. 
+1. When the ODROID-N2 is recognized as a USB connected storage device, you can flash the eMMC with [Etcher](https://www.balena.io/etcher/).
+   * Use the latest stable version of Home Assistant OS for the [ODROID-N2+](https://github.com/home-assistant/operating-system/releases/download/{{site.data.version_data.hassos['odroid-n2']}}/haos_odroid-n2-{{site.data.version_data.hassos['odroid-n2']}}.img.xz) (haos_odroid-n2-{{site.data.version_data.hassos['odroid-n2']}}.img.xz).
 
-When the flash process is complete, disconnect the ODROID-N2+ from your PC and remove the power cable. Remove the USB and HDMI cable, and make sure to toggle the boot mode switch back to MMC.
+1. When the flash process is complete, disconnect the ODROID-N2+ from your PC.
+   * Remove the power cable.
+   * Remove the USB and HDMI cables.
+   * Make sure to toggle the boot mode switch back to MMC.
 
-Once it is back in its case, connect your ODROID-N2+ to your network with an Ethernet cable and plug in power.
+1. Put the ODROID back in its case.
+1. Connect your ODROID-N2+ to your network with an Ethernet cable and plug in power.
 
-If your router supports mDNS, you will be able to reach your installation on `http://homeassistant.local:8123`.  If your network doesn’t support mDNS, you’ll have to use the IP address of your ODROID-N2+ instead of `homeassistant.local`. For example, `http://192.168.0.9:8123`. You should be able to find the IP address of your ODROID-N2+ from the admin interface of your router.
+1. If your router supports mDNS, you can reach your installation at `http://homeassistant.local:8123`. 
+   * If your network doesn’t support mDNS, you’ll have to use the IP address of your ODROID-N2+ instead of `homeassistant.local`. For example, `http://192.168.0.9:8123`. 
+   * You should be able to find the IP address of your ODROID-N2+ from the admin interface of your router.
+1. Continue with [onboarding](/getting-started/onboarding/).
\ No newline at end of file