diff --git a/source/_components/binary_sensor.opentherm_gw.markdown b/source/_components/binary_sensor.opentherm_gw.markdown new file mode 100644 index 00000000000..decdf3b7397 --- /dev/null +++ b/source/_components/binary_sensor.opentherm_gw.markdown @@ -0,0 +1,24 @@ +--- +layout: page +title: "OpenTherm Gateway Binary Sensor" +description: "Expose internal data from the OpenTherm Gateway." +date: 2018-10-19 18:23 +sidebar: true +comments: false +sharing: true +footer: true +logo: opentherm.png +ha_category: Binary Sensor +ha_release: 0.81 +ha_iot_class: "Local Push" +--- + +The `opentherm_gw` binary sensor platform is used to expose internal data from the [OpenTherm Gateway](http://otgw.tclcode.com/) in Home Assistant. + +# {% linkable_title Configuration %} + +Configuration of this platform is achieved through the [OpenTherm Gateway Hub](/components/opentherm_gw/) configuration. + +

+The OpenTherm protocol is based on polling. The thermostat sends requests to the boiler at specific intervals. As a result, it may take some time for changes to propagate between Home Assistant and the thermostat. +

diff --git a/source/_components/opentherm_gw.markdown b/source/_components/opentherm_gw.markdown index ac025198670..62aa3def7f5 100644 --- a/source/_components/opentherm_gw.markdown +++ b/source/_components/opentherm_gw.markdown @@ -92,10 +92,20 @@ monitored_variables: description: Hot water 2 temperature. exhaust_temp: description: Boiler exhaust temperature. + master_ch2_enabled: + description: Thermostat requests central heating 2 on. + master_ch_enabled: + description: Thermostat requests central heating on. + master_cooling_enabled: + description: Thermostat requests cooling. + master_dhw_enabled: + description: Thermostat requests hot water to be heated. master_memberid: description: Thermostat member ID. master_ot_version: description: Thermostat OpenTherm protocol version. + master_otc_enabled: + description: Thermostat is using outside temperature correction. master_product_type: description: Thermostat product type. master_product_version: @@ -114,8 +124,14 @@ monitored_variables: description: OpenTherm Gateway hot water override status. otgw_gpio_a: description: OpenTherm Gateway GPIO port A operating mode. + otgw_gpio_a_state: + description: OpenTherm Gateway GPIO A state. otgw_gpio_b: description: OpenTherm Gateway GPIO port B operating mode. + otgw_gpio_b_state: + description: OpenTherm Gateway GPIO B state. + otgw_ignore_transitions: + description: OpenTherm Gateway ignores ripples in the signal during high/low transitions. otgw_led_a: description: OpenTherm Gateway LED A operating mode. otgw_led_b: @@ -130,6 +146,8 @@ monitored_variables: description: OpenTherm Gateway LED F operating mode. otgw_mode: description: OpenTherm Gateway operating mode. + otgw_ovrd_high_byte: + description: OpenTherm Gateway overrides high byte with message ID 100. otgw_setback_temp: description: OpenTherm Gateway setback temperature for `away mode`. otgw_setpoint_ovrd_mode: @@ -144,6 +162,14 @@ monitored_variables: description: Outside temperature as reported in the OpenTherm protocol. relative_mod_level: description: Relative modulation level. + remote_rw_dhw: + description: Boiler supports writing hot water setpoint. + remote_rw_max_ch: + description: Boiler supports writing maximum central heating setpoint. + remote_transfer_dhw: + description: Boiler supports reading hot water setpoint. + remote_transfer_max_ch: + description: Boiler supports reading maximum central heating setpoint. return_water_temp: description: Boiler return water temperature. room_setpoint: @@ -154,14 +180,50 @@ monitored_variables: description: Room target temperature override value. room_temp: description: Current room temperature. + rovrd_auto_prio: + description: Programmed room setpoint change takes priority over remote override setting. + rovrd_man_prio: + description: Manual room setpoint change takes priority over remote override setting. + slave_air_pressure_fault: + description: Boiler reports air pressure fault. + slave_ch2_active: + description: Boiler reports central heating 2 active. + slave_ch2_present: + description: Boiler has a central heating 2 circuit. + slave_ch_active: + description: Boiler reports central heating active. slave_ch_max_setp: description: Maximum boiler supported central heating water target temperature. slave_ch_min_setp: description: Minimum boiler supported central heating water target temperature. + slave_control_type: + description: Boiler control type ('off' is modulating, 'on' is on/off). + slave_cooling_active: + description: Boiler reports cooling active. + slave_cooling_supported: + description: Boiler supports cooling. + slave_dhw_active: + description: Boiler reports hot water active. + slave_dhw_config: + description: Boiler hot water mode ('off' is instantaneous or unspecified, 'on' is storage tank). slave_dhw_max_setp: description: Maximum boiler supported hot water target temperature. slave_dhw_min_setp: description: Minimum boiler supported hot water target temperature. + slave_dhw_present: + description: Boiler reports hot water present. + slave_diagnostic_indication: + description: Boiler diagnostic indication. + slave_fault_indication: + description: Boiler fault indication. + slave_flame_on: + description: Boiler reports flame on. + slave_gas_fault: + description: Boiler reports gas fault. + slave_low_water_pressure: + description: Boiler reports low water pressure. + slave_master_low_off_pump: + description: Boiler supports low-off and pump control commands (this sensor is inverted, 'on' is not supported, 'off' is supported) slave_max_capacity: description: Maximum boiler capacity. slave_max_relative_modulation: @@ -178,6 +240,12 @@ monitored_variables: description: Boiler product type. slave_product_version: description: Boiler product version. + slave_remote_reset: + description: Boiler reports 'lockout-reset' supported. + slave_service_required: + description: Boiler reports service required. + slave_water_overtemp: + description: Boiler reports water overtemperature. solar_coll_temp: description: Solar collector temperature. solar_storage_temp: