---
layout: page
title: "Z-Wave Device Specific Settings"
description: "Notes for specific Z-Wave devices."
date: 2016-03-24 08:49 -0700
sidebar: true
comments: false
sharing: true
footer: true
redirect_from: /getting-started/z-wave-device-specific/
---
## {% linkable_title Device Categories %}
### {% linkable_title Motion or alarm sensors %}
In order for Home Assistant to recognize the sensor properly, you will need to change its configuration from `Basic Set (default)` to `Binary Sensor report` or `Alarm report`.
These devices will either show as a binary sensor or a sensor called `Alarm xxxx` and will report a numeric value. Test to see what value is what. Sometimes this is noted in the device manual.
You can set the settings of the Z-Wave device through the Z-Wave control panel.
### {% linkable_title Locks and other secure devices %}
These devices require a network key to be set for the Z-Wave network before they are paired, using the **Add Node Secure** option.
Home Assistant stores logs from Z-Wave in `OZW_log.txt` in the Home Assistant config directory, when you pair a secure device you should see communication from the node with lines starting with `info: NONCES` in `OZW_log.txt` when the device is paired successfully with a secure connection.
### {% linkable_title Specific Devices %}
### {% linkable_title Aeotec Z-Stick %}
It's totally normal for your Z-Wave stick to cycle through its LEDs (Yellow, Blue and Red) while plugged into your system. If you don't like this behavior it can be turned off.
Use the following example commands from a terminal session on your Pi where your Z-Wave stick is connected.
Turn off "Disco lights":
```bash
$ echo -e -n "\x01\x08\x00\xF2\x51\x01\x00\x05\x01\x51" > /dev/serial/by-id/usb-0658_0200-if00
```
Turn on "Disco lights":
```bash
$ echo -e -n "\x01\x08\x00\xF2\x51\x01\x01\x05\x01\x50" > /dev/serial/by-id/usb-0658_0200-if00
```
### {% linkable_title Razberry Board %}
You need to disable the on-board Bluetooth since the board requires the use of the hardware UART (and there's only one on the Pi3). You do this by adding the following to the end of `/boot/config.txt`:
```text
dtoverlay=pi3-disable-bt
```
Then disable the Bluetooth modem service:
```bash
$ sudo systemctl disable hciuart
```
Once Bluetooth is off, enable the serial interface via the `raspi-config` tool. After reboot run:
```bash
$ sudo systemctl mask serial-getty@ttyAMA0.service
```
so that your serial interface looks like:
```text
crw-rw---- 1 root dialout 204, 64 Sep 2 14:38 /dev/ttyAMA0
```
at this point simply add your user (homeassistant) to the dialout group:
```bash
$ sudo usermod -a -G dialout homeassistant
```
Finally, reboot again to make those changes active. It's has been tested on hassbian and has been reported that this is also required on the Pi2.
If you've installed the Z-Way software, you'll need to ensure you disable it before you install Home Assistant or you won't be able to access the board. Do this with `sudo /etc/init.d/z-way-server stop; sudo update-rc.d z-way-server disable`.
### {% linkable_title Aeon Minimote %}
Here's a handy configuration for the Aeon Labs Minimote that defines all possible button presses. Put it into `automation.yaml`.
```yaml
- id: mini_1_pressed
alias: 'Minimote Button 1 Pressed'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 1
- id: mini_1_held
alias: 'Minimote Button 1 Held'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 2
- id: mini_2_pressed
alias: 'Minimote Button 2 Pressed'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 3
- id: mini_2_held
alias: 'Minimote Button 2 Held'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 4
- id: mini_3_pressed
alias: 'Minimote Button 3 Pressed'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 5
- id: mini_3_held
alias: 'Minimote Button 3 Held'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 6
- id: mini_4_pressed
alias: 'Minimote Button 4 Pressed'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 7
- id: mini_4_held
alias: 'Minimote Button 4 Held'
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.aeon_labs_minimote_1
scene_id: 8
```
### {% linkable_title Zooz Toggle Switches %}
Some models of the Zooz Toggle switches ship with an instruction manual with incorrect instruction for Z-Wave inclusion/exclusion. The instructions say that the switch should be quickly switched on-off-on for inclusion and off-on-off for exclusion. However, the correct method is on-on-on for inclusion and off-off-off for exclusion.
## {% linkable_title Central Scene configuration %}
To provide Central Scene support you need to shut Home Assistant down and modify your `zwcfg_*.xml` file according to the following guides.
### {% linkable_title Inovelli Scene Capable On/Off and Dimmer Wall Switches %}
For Inovelli switches, you'll need to update (or possibly add) the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Once this is complete, you should see the follow `zwave.scene_activated` events:
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Double tap off|1|3
Double tap on|2|3
Triple tap off|1|4
Triple tap on|2|4
4x tap off|1|5
4x tap on|2|5
5x tap off|1|6
5x tap on|2|6
### {% linkable_title HomeSeer Switches %}
For the HomeSeer devices specifically, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the HomeSeer devices (as a reference for other similar devices):
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Single tap on|1|0
Single tap off|2|0
Double tap on|1|3
Double tap off|2|3
Triple tap on|1|4
Triple tap off|2|4
Tap and hold on|1|2
Tap and hold off|2|2
Some installations will see those details:
**Top button ID: 1, Bottom ID: 2**
**Action**|**scene\_data**
:-----:|:-----:
Single Press|7800
Hold Button|7740
2x Tap|7860
3x Tap|7920
4x Tap|7980
5x Tap|8040
### {% linkable_title Fibaro Button FGPB-101-6 v3.2 %}
For the Button, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Button (as a reference for other similar devices):
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Single tap on|1|0
Double tap on|1|3
Triple tap on|1|4
Tap and hold wakes up the Button.
### {% linkable_title Fibaro Keyfob FGKF-601 %}
For the Fibaro Keyfob, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Keyfob (as a reference for other similar devices):
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Button one (Square) single tap|1|7680
Button one (Square) hold|1|7800
Button one (Square) release|1|7740
Button two (Circle) single tap|2|7680
Button two (Circle) hold|2|7800
Button two (Circle) release|2|7740
Button three (X) single tap|3|7680
Button three (X) hold|3|7800
Button three (X) release|3|7740
Button four (Triangle) single tap|4|7680
Button four (Triangle) hold|4|7800
Button four (Triangle) release|4|7740
Button five (Triangle) single tap|5|7680
Button five (Triangle) hold|5|7800
Button five (Triangle) release|5|7740
Button six (Triangle) single tap|6|7680
Button six (Triangle) hold|6|7800
Button six (Triangle) release|6|7740
Press circle and plus simultaneously to wake up the device.
### {% linkable_title Aeotec Wallmote %}
For the Aeotec Wallmote, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Wallmote (as a reference for other similar devices):
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Button one single tap|1|0
Button one hold|1|2
Button one release|1|1
Button two single tap|2|0
Button two hold|2|2
Button two release|2|1
Button three single tap|3|0
Button three hold|3|2
Button three release|3|1
Button four single tap|4|0
Button four hold|4|2
Button four release|4|1
### {% linkable_title WallC-S Switch %}
Use the same configuration as for the Aeotec Wallmote.
### {% linkable_title HANK One-key Scene Controller HKZN-SCN01 %}
For the HANK One-key Scene Controller, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Button (as a reference for other similar devices):
**Action**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:
Button single tap|1|0
Button hold|1|2
Button release|1|1
### {% linkable_title HANK Four-key Scene Controller HKZN-SCN04 %}
For the HANK Four-key Scene Controller, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Buttons and associated Pictogram:
**Action**|**Pictogram**|**scene\_id**|**scene\_data**
:-----:|:-----:|:-----:|:-----:
Button one tap|Moon and Star|1|0
Button one hold|Moon and Star|1|2
Button one release|Moon and Star|1|1
Button two tap|People|2|0
Button two hold|People|2|2
Button two release|People|2|1
Button three tap|Circle|3|0
Button three hold|Circle|3|2
Button three release|Circle|3|1
Button four tap|Circle with Line|4|0
Button four hold|Circle with Line|4|2
Button four release|Circle with Line|4|1
### {% linkable_title RFWDC Cooper 5-button Scene Control Keypad %}
For the RFWDC Cooper 5-button Scene Control Keypad, you may need to update the `COMMAND_CLASS_CENTRAL_SCENE` for each node in your `zwcfg` file with the following:
```xml
```
Below is a table of the action/scenes for the Buttons:
**Action**|**scene\_id**
:-----:|:-----:
Button one tap|1
Button two tap|2
Button three tap|3
Button four tap|4
Button five tap|5
When a button turns off, the controller sends `basic_set` in a generic `node_event` and does not specify which button was pressed. The status of the buttons is encoded into the `indicator` value, so in order to determine the status of each button, you need to refresh the indicator value. You can also control the LEDs for each button by setting the indicator value. For responsiveness, automations should be triggered with `zwave.scene_activated` events rather than the switch status.
Here is an example configuration needed for the scene controller:
{% raw %}
```yaml
automation:
- alias: Sync the indicator value on button events
trigger:
- platform: event
event_type: zwave.scene_activated
event_data:
entity_id: zwave.scene_contrl
- platform: event
event_type: zwave.node_event
event_data:
entity_id: zwave.scene_contrl
action:
- service: zwave.refresh_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
switch:
- platform: template
switches:
button_1_led:
value_template: "{{ states('sensor.scene_contrl_indicator')|int|bitwise_and(1) > 0 }}"
turn_on:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int + 1 }}"
turn_off:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int - 1 }}"
button_2_led:
value_template: "{{ states('sensor.scene_contrl_indicator')|int|bitwise_and(2) > 0 }}"
turn_on:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int + 2 }}"
turn_off:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int - 2 }}"
button_3_led:
value_template: "{{ states('sensor.scene_contrl_indicator')|int|bitwise_and(4) > 0 }}"
turn_on:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int + 4 }}"
turn_off:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int - 4 }}"
button_4_led:
value_template: "{{ states('sensor.scene_contrl_indicator')|int|bitwise_and(8) > 0 }}"
turn_on:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states(scene_contrl_indicator)|int + 8 }}"
turn_off:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int - 8 }}"
button_5_led:
value_template: "{{ states('sensor.scene_contrl_indicator')|int|bitwise_and(16) > 0 }}"
turn_on:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int + 16 }}"
turn_off:
service: zwave.set_node_value
data_template:
node_id: 3
value_id: "{{ state_attr('sensor.scene_contrl_indicator','value_id') }}"
value: "{{ states('sensor.scene_contrl_indicator')|int - 16 }}"
```
{% endraw %}