Untested device configs

user_setups/esp32/esp32-tft-touch.ini

@@ -0,0 +1,51 @@
+;***************************************************;
+;       ESP32 TFT Touch with camera 3.5" Capacitive ;
+;               - 3.5" ili9488 TFT SPI 4-WIRE       ;
+;               - ft6336 touch controller           ;
+;***************************************************;
+; untested config
+
+[env:esp32-tft-touch-35]
+extends = esp32
+board = esp32dev
+
+build_flags =
+    ${env.build_flags}
+    ${esp32.build_flags}
+    ${esp32.hspi}        ; Use VSPI hardware SPI bus
+    -D HASP_MODEL="ESP32 TFT Touch 3.5"
+
+;region -- TFT_eSPI build options ------------------------
+    -D USER_SETUP_LOADED=1
+    -D ILI9488_DRIVER=1
+    -D TFT_ROTATION=0 ; 0=0, 1=90, 2=180 or 3=270 degree
+    -D TFT_WIDTH=320
+    -D TFT_HEIGHT=480
+    -D TFT_CS=15  ;// SS Chip select control pin
+    -D TFT_DC=33  ;// RS Data Command control pin
+    -D TFT_RST=-1 ;// Reset pin (could connect to RST pin)
+    -D TFT_BCKL=32  ;None, configurable via web UI (e.g. 2 for D4)
+    -D SUPPORT_TRANSACTIONS
+    -D TOUCH_DRIVER=6336 ; FT6336 Capacitive touch panel driver 
+    -D TOUCH_SDA=26
+    -D TOUCH_SCL=27
+    -D TOUCH_IRQ=0
+    -D TOUCH_RST=-1   ; not used
+    -D TOUCH_FREQUENCY=400000
+    -D SPI_FREQUENCY=40000000
+    -D SPI_READ_FREQUENCY=20000000
+;endregion
+
+; -- Debugging options -----------------------------
+;   -D CORE_DEBUG_LEVEL=ARDUHAL_LOG_LEVEL_DEBUG
+
+;region -- Library options -------------------------------
+lib_deps =
+    ${env.lib_deps}
+    ${esp32.lib_deps}
+    git+https://github.com/aselectroworks/Arduino-FT6336U.git
+
+lib_ignore =
+    ${env.lib_ignore}
+    ${esp32.lib_ignore}
+;endregion

user_setups/esp32/nscreen32.ini

@@ -0,0 +1,63 @@
+;***************************************************;
+;       YeaCreate Nscreen32                         ;
+;               - 4" ST7796 TFT 8-biy parallell     ;
+;               - gt911 touch controller            ;
+;***************************************************;
+; untested config
+
+[env:yeacreate-nscreen32]
+extends = esp32
+board = esp32dev
+
+build_flags =
+    ${env.build_flags}
+    ${esp32.build_flags}
+    ${esp32.hspi}        ; Use VSPI hardware SPI bus
+    -D HASP_MODEL="YeaCreate Nscreen32"
+
+;region -- TFT_eSPI build options ------------------------
+    -D USER_SETUP_LOADED=1
+    -D ST7796_DRIVER=1
+    -D ESP32_PARALLEL=1
+    -D TFT_ROTATION=0 ; 0=0, 1=90, 2=180 or 3=270 degree
+    -D TFT_WIDTH=320
+    -D TFT_HEIGHT=480
+    ; ESP32 pins used for the parallel interface TFT
+    -D TFT_CS=33    ; Chip select control pin
+    -D TFT_DC=15    ; Data Command control pin - must use a pin in the range 0-31 also named RS
+    -D TFT_WR=4     ; Write strobe control pin - must use a pin in the range 0-31
+    -D TFT_RD=2
+    -D TFT_D0=12    ; Must use pins in the range 0-31 for the data bus
+    -D TFT_D1=13    ; so a single register write sets/clears all bits
+    -D TFT_D2=26
+    -D TFT_D3=25
+    -D TFT_D4=19
+    -D TFT_D5=18
+    -D TFT_D6=27
+    -D TFT_D7=14
+    -D TFT_RST=32   ; Reset pin
+    ;-D TFT_BCKL=32  ;None, configurable via web UI (e.g. 2 for D4)
+    -D SUPPORT_TRANSACTIONS
+    -D TOUCH_DRIVER=911  ; GT911 Capacitive touch panel driver 
+    -D TOUCH_SDA=21
+    -D TOUCH_SCL=22
+    -D TOUCH_IRQ=5
+    -D TOUCH_RST=23
+    -D TOUCH_FREQUENCY=400000
+    -D SPI_FREQUENCY=40000000
+    -D SPI_READ_FREQUENCY=20000000
+;endregion
+
+; -- Debugging options -----------------------------
+;   -D CORE_DEBUG_LEVEL=ARDUHAL_LOG_LEVEL_DEBUG
+
+;region -- Library options -------------------------------
+lib_deps =
+    ${env.lib_deps}
+    ${esp32.lib_deps}
+    git+https://github.com/aselectroworks/Arduino-FT6336U.git
+
+lib_ignore =
+    ${env.lib_ignore}
+    ${esp32.lib_ignore}
+;endregion