* Fix NetworkManager connection name for VLANs
The connection name for VLANs should include the parent interface name
for better identification. This was originally the intention, but the
interface object's name property was used which appears empty at that
point.
* Disallow creating multiple connections for the same VLAN id
Only allow a single connection per interface and VLAN id. The regular
network commands can be used to alter the configuration.
* Fix pytest
* Simply connection id name generation
Always rely on the Supervisor interface representation's name attribute
to generate the NetworkManager connection id. Make sure that the name
is correctly set when creating VLAN interfaces as well.
* Special case VLAN configuration
We can't use the match information when comparing Supervisor interface
representation with D-Bus representations. Special case VLAN and
compare using VLAN ID and parent interface.
Note that this currently compares connection UUID of the parent
interface.
* Fix pytest
* Separate VLAN creation logic from apply_changes
Apply changes is really all about updating the NetworkManager settings
of a particular network interface. The base in apply_changes() is
NetworkInterface class, which is the NetworkManager Device abstraction.
All physical interfaces have such a Device hence it is always present.
The only exception is when creating a VLAN: Since it is a virtual
device, there is no device when creating a VLAN.
This separate the two cases. This makes it much easier to reason if
a VLAN already exists or not, and to handle the case where a VLAN
needs to be created.
For all other network interfaces, the apply_changes() method can
now rely on the presence of the NetworkInterface Device abstraction.
* Add VLAN test interface and VLAN exists test
Add a test which checks that an error gets raised when a VLAN for a
particular interface/id combination already exists.
* Address pylint
* Fix test_ignore_veth_only_changes pytest
* Make VLAN interface disabled to avoid test issues
* Reference setting 38 in mocked connection
* Make sure interface type matches
Require a interface type match before doing any comparision.
* Add Supervisor host network configuration tests
* Fix device type checking
* Fix pytest
* Fix tests by taking VLAN interface into account
* Fix test_load_with_network_connection_issues
This seems like a hack, but it turns out that the additional active
connection caused coresys.host.network.update() to be called, which
implicitly "fake" activated the connection. Now it seems that our
mocking causes IPv4 gateway to be set.
So in a way, the test checked a particular mock behavior instead of
actual intention.
The crucial part of this test is that we make sure the settings remain
unchanged. This is done by ensuring that the the method is still auto.
* Fix test_check_network_interface_ipv4.py
Now that we have the VLAN interface active too it will raise an issue
as well.
* Apply suggestions from code review
Co-authored-by: Mike Degatano <michael.degatano@gmail.com>
* Fix ruff check issue
---------
Co-authored-by: Mike Degatano <michael.degatano@gmail.com>
* Delay inital version fetch until there is connectivity
* Add test
* Only mock get not whole websession object
* drive delayed fetch off of supervisor connectivity not host
* Fix test to not rely on sleep guessing to track tasks
* Use fixture to remove job throttle temporarily
* Improve WiFi settings error handling
Currently, the frontend potentially provides no WiFi settings dictionary
but still tries to update other (IP address) settings on the interface.
This leads to a stack trace since network manager is not able to fetch
the WiFi settings from the settings dictionary. Simply fill out what
we can and let NetworkManager provide an error.
Also allow to disable a network interface which has no configuration.
This avoids an error when switching to auto and back to disabled then
press save on a new wireless network interface.
* Add debug message when already disabled
* Add pytest for incomplete WiFi settings as psoted by frontend
Simulate the frontend posting no WiFi settings. Make sure the Supervisor
handles this gracefully.
* Migrate to Ruff for lint and format
* Fix pylint issues
* DBus property sets into normal awaitable methods
* Fix tests relying on separate tasks in connect
* Fixes from feedback
